Free help in LA & Orange CountyCheck your ZIP
How-To Guide
13 min
November 8, 2026

Water Heater Leaking From the Bottom: What It Means and What to Do

Water under your water heater? Find the source in 5 checks, learn what's safe, what it costs, and when the tank needs replacing. LA and OC facts.

Water at the bottom of a water heater usually comes from one of four places: condensation, the temperature and pressure (T&P) relief valve, the drain valve, or a loose fitting on top that drips down the side. If the tank itself is leaking, plan on a new water heater, because manufacturers say a tank that is confirmed to be leaking should be replaced, not repaired (A.O. Smith).

The good news is that a lot of puddles are not the tank. A.O. Smith's own leak bulletin says many suspected "leakers" are not leaking tanks. Here's how to stay safe, find the source in a few minutes, and what each answer means for your wallet in LA and Orange County.

Animated drawing: where water at the bottom of a tank water heater can come fromA gas tank water heater with cold water flowing in, hot water flowing out, gas flowing to the burner and a flickering flame. Five numbered spots take turns showing water: 1 condensation on the tank and burner, 2 the T&P relief valve opening and water running down its pipe, 3 the drain valve dripping, 4 a fitting on top dripping down the side, 5 rust at the tank bottom with water seeping into the drain pan. Also shown: the cold-water shutoff, two earthquake straps, a drain pan, and sediment inside the tank. 1 2 3 4 5 Condensation T&P relief valve pipe Drain valve Fittings on top Tank bottom
The five places to check: (1) condensation on the tank or burner, which is normal; (2) the T&P relief valve pipe; (3) the drain valve; (4) the fittings on top; (5) the tank itself. Also shown: cold water in (blue), hot water out (red), the gas line, the cold-water shutoff, two earthquake straps, a drain pan, and sediment inside the tank. Original drawing by PlumberNearMe.ai.

First: Is Anything Unsafe Right Now?

Check these before you start looking for the leak:

  • Smell gas? Leave the house. Don't switch lights or appliances on or off. Call SoCalGas at 1-800-427-2200 from outside, or call 911 (SoCalGas).
  • Water spreading? Close the cold-water valve on the pipe that goes into the top of the heater (Irvine Ranch Water District). If you can't reach it, shut off the water to the house.
  • More than a few drops? Turn off the heat. On a gas heater, set the gas control on the front to OFF. On an electric heater, switch off its breaker before you touch anything (A.O. Smith).
  • Has any part of a gas heater been under water? Don't use it. Rheem, A.O. Smith, and Bradford White manuals all say not to use a heater if any part has been under water, and A.O. Smith says a flooded heater should be replaced (A.O. Smith Bulletin 0823).
  • Electric heater? Leave the breaker off until the tank is full again. Heating a tank that isn't full of water can burn out the element. Manufacturers call this dry firing, and it isn't covered by the warranty (A.O. Smith manual).
  • Keep your hands away from the T&P pipe. When that valve opens, the water coming out can be scalding.

Is It a Leak, or Just Condensation?

Condensation is the most common false alarm. A tank full of cold water is cool on the outside, so moisture condenses on it and drips down. It happens most when a heater is new, after it's refilled with cold water, or after a long run of hot water. On a gas heater, the drops can fall on the burner and make a sizzling sound (Bradford White). A.O. Smith says a typical home water heater makes about half a gallon of water vapor for every hour it runs (A.O. Smith Bulletin 15).

Condensation stops once the tank is hot. A.O. Smith puts that point at above 110°F (Bulletin 51). No manufacturer gives a time, so use this simple test:

  1. Wipe the tank and floor dry, and put down dry paper towels.
  2. Let the heater finish heating.
  3. Look again. A few drops that stop once the tank is hot are condensation. Water that keeps pooling is a leak.
Animation: the paper towel test for condensation or a leakTwo water heaters with drops running down their sides. Each is wiped dry and gets a paper towel underneath, then heats up. On the left the drops stop and the towel stays dry: condensation. On the right the towel keeps getting wetter: a leak.Dry: condensationWet: a leakWater under the heater?1. Wipe it dry, put down a paper towel2. Let the heater finish heating3. Look againDry: condensation. Wet: a leak.
The paper towel test: condensation stops once the tank is hot. A leak keeps going.

Rheem says the same thing: small amounts of condensation are normal, but pooling water means there's a problem (Rheem). A short sizzle when a gas heater starts from cold is normal. Water that keeps dripping onto the burner after the tank is hot isn't, so turn the heater off and have it looked at (Rheem).

Find the Leak in 5 Checks

Go through these in order. Water runs down, so the first wet spot you see is not always where the leak starts: look for the highest wet spot on the heater.

Safety first. Smell gas? Leave and call SoCalGas at 1-800-427-2200 or 911 from outside. Water spreading? Close the cold-water valve on top of the heater. Has any part of a gas heater been under water? Don't use it.

  1. Animation: condensation on a cold tank dries up as the tank heatsDrops bead up on the side of a cold water heater and run down. A thermometer rises as the tank heats, and the drops stop.

    1Small drops on the tank, or a sizzle at the burner, on a new heater or after a lot of hot water use?

    Yes: Probably condensation. It stops once the tank is hot. If water keeps pooling after that, go to check 2.

    No: Go to check 2.

  2. Animation: the T&P relief valve lets water out through its pipeThe relief valve on the side of the tank jumps open in short bursts and water rushes down its discharge pipe.

    2Is water coming out of the pipe that runs down from the T&P relief valve near the top of the tank?

    Yes: The valve is letting out pressure or heat. Don't cap or plug it. Have the water pressure and the expansion tank checked.

    No: Go to check 3.

  3. Animation: the drain valve drips and a puddle growsDrops form at the spout of the drain valve near the bottom of the tank and fall, and a puddle spreads on the floor.

    3Is the small spigot near the bottom (the drain valve) dripping?

    Yes: Make sure it's fully closed. If it still drips, the valve or its washer needs replacing.

    No: Go to check 4.

  4. Animation: a leak at a fitting on top runs down the side of the tankA drop forms where the cold water pipe meets the top of the tank, runs across the top and down the side, leaving a wet trail.

    4Is the top of the tank wet around the pipes, with a wet trail running down the side?

    Yes: The leak is up top, not at the bottom. A connection or fitting needs tightening, resealing, or replacing.

    No: Go to check 5.

  5. Animation: sediment builds up, the tank rusts and water weeps out the bottomSediment builds up inside the bottom of the tank, rust spreads along the bottom seam, and water weeps out into the drain pan.

    5Is water coming from the tank body or the bottom seam, often with rust, while everything above is dry?

    Yes: The tank is probably leaking. Close the cold-water valve, turn off the gas or power, and plan a replacement.

    Not sure: Dry everything, then watch where water shows up first.

Still not sure? Snap the label in the free Water Heater Check to see how old the heater is and what to do next.

Why Is Water Coming Out of the T&P Relief Valve Pipe?

The temperature and pressure relief valve sits near the top of the tank, with a pipe running down from it. It's a safety valve: it opens when the pressure or the temperature inside the tank gets too high. Water at the end of that pipe means the valve is doing its job, or that the valve is worn out.

Animation: why a T&P relief valve drips, and how an expansion tank stops itA water heater heats up. The water expands, a pressure gauge on the cold line climbs into the red, and the relief valve opens and lets water out through its pipe. Then an expansion tank is added on the cold line: when the water heats again, the tank takes up the extra water, the gauge stays in the middle, and the valve stays shut.expansion tankWhy does the relief valve drip?1. Water expands as it heats2. The pressure climbs too high3. The relief valve lets water out4. Add an expansion tank5. It takes up the extra waterThe pressure stays safe. No drip.
Relief valve: it opens when pressure gets too high. An expansion tank, or lower house pressure, usually stops the drip.

The most common cause is pressure. A.O. Smith says a small drip from the valve usually means the home's water pressure is too high (A.O. Smith Bulletin 52). Water also expands as it heats. If your water line has a check valve or backflow preventer (a "closed" system), that extra pressure has nowhere to go. Bradford White notes that in that case the relief valve will drip every time the heater turns on (Bradford White), and Rheem's bulletin on relief valves says replacing the valve won't fix a thermal expansion problem (Rheem).

What to do:

  • Never cap or plug the valve or its pipe. Every manufacturer warns against it.
  • Check your water pressure. In Los Angeles, new plumbing needs a pressure regulator whenever pressure from the city main can go over 80 psi, and regulators are usually set between 50 and 70 psi. The property owner installs and maintains it, and older homes may not have one (LADWP). LADWP will tell you the highest and lowest pressure at your address for free.
  • Ask about an expansion tank. The 2025 California Plumbing Code, in effect since January 1, 2026, requires an expansion tank or a similar device when a check valve, backflow preventer, or other device keeps pressure from flowing back to the main (Section 608.3). City checklists for the 2025 code say tankless heaters don't need one (City of San Ramon).
  • Check the temperature. The U.S. Consumer Product Safety Commission urges setting water heaters to 120°F to prevent scalds (CPSC). If the pipe is spitting very hot water or steam, turn the heater off and call a plumber now.
  • Replace the valve if it won't close. Manufacturers say to test the valve about once a year by lifting its lever. If it keeps letting water out afterward, it needs to be replaced (A.O. Smith Bulletin 52). If yours hasn't been tested in years, let a plumber do the first test, since an old valve may not close again.

A new pressure regulator typically runs $200 to $500, and adding an expansion tank runs $200 to $500.

The pipe itself has rules too. Under Section 608.5 of the 2025 code, it can't have a valve in it, it can't empty into the water heater's drain pan, and outdoors it has to end between 6 and 24 inches above the ground, pointing down. Anaheim prints the height rule on its plumbing permit application (City of Anaheim), and other cities' 2025 handouts spell out the rest (City of Roseville).

Is the Drain Valve Leaking?

The drain valve is the small spigot near the bottom of the tank, used to flush it. Look for drips from the spout or water around the base of the valve.

  • Make sure it's fully closed. Turn the handle clockwise by hand. A.O. Smith's first check for a puddle is whether the drain valve is closed tightly. If the handle won't stop the drip, replace the valve (A.O. Smith Bulletin 51).
  • Some valves have a washer you can replace. Some models come with plastic drain valves, and the manual shows how to replace the washer (State water heater manual).
  • Water around the base of the valve, where it screws into the tank, can mean it's leaking at that fitting.

A dripping drain valve isn't an emergency, but it rarely fixes itself. We don't list a price for replacing one yet: we found too few published LA and Orange County prices to give a fair range. Ask for a flat price in writing. If the tank is due for a flush ($88 to $250), doing both on one visit can save a trip.

Is Water Running Down From the Top?

A leak at a fitting on top can run down the side and puddle at the bottom, so check the top before you blame the tank. Rheem's leak guide for technicians lists the pipes on top and the T&P valve as common sources (Rheem Bulletin 1234). Look for:

  • Wet pipe joints, or a white or green crust where the cold and hot pipes connect.
  • A wet spot around the anode rod fitting on top, which State's leak checklist lists as a possible source (State water heater manual).
  • On an electric heater, water around the heating element covers on the side. A.O. Smith says those gaskets can be replaced (A.O. Smith Bulletin 51).
Animation: a leak on top of a water heater can look like a leak at the bottomWater drips from a pipe fitting on top of a water heater, runs across the top and down the side, and pools on the floor at the bottom. A dotted line then traces the trail back up to the fitting, the real source.The real sourceWater at the bottom of the heater1. A fitting on top drips2. The water runs down the side3. It pools at the bottomLook for the highest wet spot
Trace it up: water runs down, so the first wet spot you see isn't always where it starts.

These leaks are usually fixable: a connector or fitting gets tightened, resealed, or replaced. A plumber's visit typically runs $75 to $175, and replacing a part such as a heating element or anode rod runs $150 to $450.

How Do You Know if the Tank Itself Is Leaking?

If water is coming from the tank body or the bottom seam, often with rust or staining, and everything above it is dry, the tank is the likely source. Rheem says leaks from the bottom often signal tank corrosion that needs a replacement (Rheem).

Animation: how a water heater tank wears out and starts to leakA cut-open water heater tank. Over the years sediment builds up on the bottom, the anode rod hanging from the top gets used up, rust spreads through the steel near the bottom, and water seeps out onto the floor. A leaking tank gets replaced, not repaired.steel tankanode rodsedimentInside a tank water heater1. Over the years, sediment builds up2. The anode rod gets used up3. The steel tank starts to rust4. Water seeps out the bottomA leaking tank gets replaced
The tank itself: once the steel rusts through, no repair holds. Manufacturers say to replace it.

Rule out everything above first. The manual for A.O. Smith's State brand says not to replace a heater until every other possible source of the water has been checked (State water heater manual). A plumber can confirm a tank leak with a pressure test: if the pressure drops slowly while every fitting stays dry, the tank may be leaking (Bradford White).

Once a tank leak is confirmed, replacement is the fix. No manufacturer manual gives a way to repair a leaking tank, and trying one can cost you the warranty: State's tank warranty says any attempt to repair a tank leak voids it (State water heater manual).

Can You Still Use a Water Heater That's Leaking?

It depends on where the water is coming from:

Where the water comes fromCan you keep using it?
Condensation that stops once the tank is hotYes
The drain valve or a fitting on topUsually, for a short time. Put a pan or bucket under it and get it fixed soon
The T&P relief valve pipeGet the pressure and temperature checked soon, and never cap the pipe. If it's spitting very hot water or steam, turn the heater off now
The tank itselfNo. Close the cold-water valve and turn off the gas or power
Any part of a gas heater has been under waterNo. Manufacturers say not to use it, and a flooded gas heater should be replaced

If you need to empty the tank, Irvine Ranch Water District's steps are a good guide: turn off the power or gas, close the supply valve on top, let the water cool, open a hot water tap in the house to let air in, then open the drain valve at the bottom (IRWD). Run a hose from the drain valve to a floor drain or outside, and give the water time to cool, because it can be scalding. On an electric heater, leave the breaker off until the tank is full again. On an old tank, sediment can clog the drain valve or keep it from closing, so if the tank isn't the problem you may want a plumber to do this.

Why Do Water Heaters in LA and Orange County Wear Out?

Hard water is a big part of it. Hard water carries calcium and magnesium, which settle as sediment in the bottom of a tank. LADWP's efficiency guide says water heaters collect solids that keep heat from reaching the water, and that keeping a heater free of deposits saves energy and helps it last longer (LADWP).

Most water in the region is hard or very hard. The USGS calls water above 180 mg/L very hard (USGS). How hard yours is depends on where it comes from, sometimes street by street. Water from the State Water Project in Northern California is much softer than Colorado River water: in the Metropolitan Water District's latest annual report, its Mills plant (all State Water Project water) averaged 84 mg/L, while its Weymouth plant averaged 272 mg/L (MWD, 2024 data).

Water supplier and areaAverage hardnessReport
LADWP: San Fernando Valley, Westside, and Central LAAbout 6 to 8 grains per gallon (103 to 140 mg/L)2025
LADWP: Harbor and Eastern LA (mostly Metropolitan Water District water)About 8 to 14 grains (140 to 236 mg/L)2025
Long Beach: most of the city (Blended Zone)4.4 grains (76 mg/L)2025
Long Beach: MWD Zone12.8 grains (220 mg/L)2025
Anaheim: local groundwater18 grains (309 mg/L)2023 report
Santa Ana: groundwater, about 85% of its supply14 grains (239 mg/L)2025
Golden State Water: Norwalk system18 grains (310 mg/L)2025 data

Your water supplier's yearly water quality report lists the hardness for your area, and the free Tap Water Check looks it up by ZIP.

Hard water is one reason to flush a tank regularly. A.O. Smith's electric manual says to drain and flush the tank at least once a year (A.O. Smith manual), and the Department of Energy's Energy Saver Guide suggests draining a quart of water every three months to remove sediment (U.S. Department of Energy). A tank flush typically runs $88 to $250. If an older tank has never been flushed, have a plumber look first: plumbers often advise against stirring up years of sediment, since it can clog the drain valve or start a leak.

Age matters too. The Department of Energy says a tank water heater lasts about 10 to 15 years (DOE). The free Water Heater Check reads your heater's age from the label.

What Does a Slow Leak Cost?

In Water

The EPA says a leak of one drip per second wastes more than 3,000 gallons a year, and the average home's leaks waste more than 9,300 gallons a year (EPA WaterSense). Here's what that water costs at LADWP's lowest home rate, $11.794 per hundred cubic feet (748 gallons) for July to December 2026 (LADWP), and at Irvine Ranch Water District's base rate of $2.92 for 2026-27 (IRWD):

LeakWater wasted in a yearLADWPIRWD
One drip per second3,000+ gallonsAbout $47About $12
A steady 50 gallons a day18,250 gallonsAbout $290About $71

That's the water charge only. Sewer and service charges come on top, and in Irvine, water that pushes you past your monthly budget is billed at higher rates ($8.03 and $19.32 per unit).

In Insurance

The California Department of Insurance's homeowners guide lists sudden and accidental water damage as typically covered, and water damage from seepage or leaks, wear and tear, and neglect as typically not covered (CDI). So a tank that suddenly lets go is the kind of loss policies usually cover, while a slow drip that soaked the floor for weeks may not be. Your policy has the final word.

If water got into floors or walls, the Department's claims guide says to stop the leak at the source, dry everything, make only temporary repairs until the adjuster has seen the damage, take photos, list what was damaged, and not throw anything out until the adjuster says so (CDI claims guide). The Department's consumer hotline is 1-800-927-4357. Water damage adds up: the average water damage and freezing claim was $15,400 from 2019 to 2023 (Insurance Information Institute).

In Mold

The EPA says to dry water-damaged areas and items within 24 to 48 hours; in most cases mold won't grow if you do (EPA). That's a target, not a promise. The California Department of Public Health says drywall, carpet, and other porous materials that stayed wet for more than a day or two may need to be removed even if they don't look moldy yet. For small spots, it recommends soap and water, not bleach (CDPH).

Repair or Replace: What Does It Cost in LA and Orange County?

JobTypical estimated range
Diagnosis or service call$75 to $175
Repair (heating element, thermostat, anode rod, or thermocouple)$150 to $450
New pressure regulator$200 to $500
Expansion tank, added on its own$200 to $500
Tank flush$88 to $250
New 40 to 50 gallon tank water heater, with permit, straps, and haul-away$1,700 to $3,500

These are typical estimated ranges for licensed plumbers in LA and Orange County, not quotes. See the pricing page for more. We don't list T&P valve or drain valve replacement yet, because we found too few published local prices to give a fair range.

Replacement usually makes sense when the tank itself is leaking, when the heater is past 10 years old, or when repairs keep coming back. If it's still under warranty, a leaking tank is usually covered with a replacement heater, but labor, the permit, and haul-away usually aren't. Tank warranties run from 1 to 12 years depending on the model, so check yours: we explain the rules for Rheem, A.O. Smith, and Bradford White.

What Does a Replacement Need in LA and Orange County?

A Permit

Every city we checked requires a permit to replace a water heater: Los Angeles, unincorporated LA County, Long Beach, Anaheim, Santa Ana, Irvine, Huntington Beach, and Bellflower. In Los Angeles it's an express permit you can get online through PermitLA. Here's about what the permit costs, worked out from each city's fee schedule as of November 2026:

CityPermit for a water heater
Los AngelesAbout $60, or about $98 with an expansion tank (LADBS)
Unincorporated LA CountyAbout $64 (LA County)
Long Beach$100 minimum on the October 2025 schedule (Long Beach)
Anaheim$188, the city's minimum permit fee (Anaheim)
IrvineAbout $70 (Irvine)
Huntington BeachAbout $98 (Huntington Beach)
Santa Ana and BellflowerCheck with the city. We couldn't confirm a current fee online (Santa Ana, Bellflower)

The replacement range in our price table already includes the permit. Ask whether your quote does too.

Code Upgrades

Under the 2025 California Plumbing Code, a new or replacement tank needs:

  • Earthquake straps. At least two, one in the upper third of the tank and one in the lower third, with the lower strap at least 4 inches above the controls (LADBS, Section 507.2). State law requires straps on every new, replacement, and existing home water heater, and a home seller has to certify it in writing (Health and Safety Code 19211). Larger tanks may need more straps, so ask your building department.
  • A drain pan where a leak would cause damage, such as in an attic or on a framed floor. It has to be at least 1.5 inches deep, with a drain at least 3/4 inch wide that ends where you can see it (Section 507.5, City of Roseville).
  • A T&P relief valve pipe that runs outside or to an approved drain, with no valve in it, ending 6 to 24 inches above the ground and pointing down. It can't empty into the pan.
  • An expansion tank if your water system is closed (see above).

The 2025 code applies to permits applied for on or after January 1, 2026 (California Building Standards Commission). Your city can add its own local rules.

A Licensed Plumber

Because the job needs a permit, it needs a licensed contractor no matter how small the price. The state's small-job exemption doesn't cover work that needs a permit (CSLB). The C-36 Plumbing license covers water heaters. Check any plumber with our free license check, and run their quote through the Quote Checker to see if the price is fair.

Not sure what you're looking at? Snap the label in the free Water Heater Check for the heater's age and what to do next, or upload a photo of the leak on our homepage for a free AI diagnosis. Facts checked November 8, 2026.

Frequently Asked Questions

Is a water heater leaking from the bottom dangerous?

The most common harm is water damage and mold. It gets dangerous if you smell gas, if water has reached a gas heater's controls or burner, or if the T&P pipe is spitting very hot water or steam. In those cases, turn the heater off and get help. For a gas smell, leave the house and call SoCalGas at 1-800-427-2200 or 911 from outside.

Why is my new water heater leaking from the bottom?

Most likely it's condensation. A new heater filled with cold water sweats until the tank heats up, and drops falling on the burner can sizzle. If water keeps pooling after the tank is hot, check the connections on top and the drain valve, and call the installer while the job is fresh.

Can a leaking water heater tank be repaired?

No manufacturer manual gives a way to repair one. A.O. Smith says a tank that is confirmed to be leaking should be replaced, and State's warranty says any attempt to repair a tank leak voids it. Valves, fittings, and gaskets can be fixed, but a leaking tank gets replaced.

Why does my water heater only leak when it's heating?

There are two usual reasons: condensation while the tank warms up from cold, or the T&P valve letting out pressure as the water expands. Bradford White notes that with thermal expansion, the relief valve drips every time the heater turns on. An expansion tank or a pressure fix usually solves the second one.

Does homeowners insurance cover a leaking water heater?

The California Department of Insurance says sudden and accidental water damage is typically covered, while damage from seepage or slow leaks, and wear and tear, typically isn't. Whether the heater itself is covered depends on your policy, so call your insurer and photograph the damage before repairs.

How long do water heaters last?

The Department of Energy says a tank water heater lasts about 10 to 15 years and a tankless heater about 20. Hard water and skipped flushes work against that, which is why LADWP recommends keeping heaters free of deposits.

Should I turn off my water heater if it's leaking?

If the tank itself is leaking, or the leak is more than a few drops, yes: close the cold-water valve on top and turn off the gas control or the breaker. For condensation, or a slow drip from the drain valve, you can usually keep using it while you arrange a repair.

Sources (53)

Not sure what you are looking at?

Upload a photo or video of the problem and get a likely diagnosis with a cost range in your area, before you call anyone.

For example: Water is leaking under my kitchen sink.

Free. We're a referral service, not a plumbing company. Photos and videos are read by AI and not stored. Costs are estimates, not quotes. Terms

Smell gas or water spreading? Get the safety steps first

  • Free to use
  • No pressure to hire
  • Local cost estimates